2008 Mercury Sable Keyless Entry Remote Programming Instructions

Easy to Follow Step-by-step Key fob remote Programming Instructions

2008 Mercury Sable

We strive to provide convenience to our customers with free keyless entry remote fob programming instructions for every single vehicle that we sell on NorthCoast Keyless.

Many people don’t know that they can purchase their own replacement vehicle entry remote, save up to 70% off of marked up Dealership prices, and program the replacement remote to their vehicle themselves. We know how good it feels to save money and do something yourself; and we aim to make it as painless as possible for you!

Free Key Fob Remote Programming Instructions for a 2008 Mercury Sable


Time needed: 2 minutes.


KEY FOB REMOTE
Step-By-Step How To Programming Instructions

  1. Prepare Vehicle

    CLOSE and UNLOCK vehicle using power door locks.

  2. Enter Vehicle Programming Mode

    INSERT key into Ignition and TURN from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm Programming Mode.

  3. Program Remote

    Within 20 seconds press any button on first keyless remote fob. Door locks will cycle to confirm programming.

    (Repeat immediately for any additional remotes to be programmed.)

  4. Exit Programming Mode

    Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.

  5. Test Remotes

    Test all remotes. Programming is now complete.

  6. Share

    If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.

Important:

  • Verify the following prior to following these instructions:
    • Your vehicle is equipped with keyless entry, and
    • You have a key fob remote that is compatible with your vehicle.
  • Obtain all remote transmitters for this vehicle. This procedure will erase all previously programmed remotes. You must program all existing and new remotes that you wish to use on the vehicle at this time.
  • You may clear your keyless entry system memory by entering programming mode as shown in the steps above.

Note: If your vehicle cannot enter programming mode, then you cannot program any remote.  This indicates either no keyless entry installed on the vehicle or a defective keyless entry receiver module.


Time needed: 3 minutes.


REMOTE HEAD KEY FOB
Step-By-Step How To Programming Instructions

  1. Confirm First Programmed Key – Step 1

    INSERT the first previously programmed transponder key into the ignition.

  2. Confirm First Programmed Key – Step 2

    TURN the ignition from Position 1 (LOCK) to Position 3 (RUN). KEEP the ignition in Position 3 (RUN) for at least 3 seconds, but no more than 10 seconds.

  3. Confirm First Programmed Key – Step 3

    TURN the ignition to Position 1 (LOCK) and REMOVE the first key from the ignition.

  4. Confirm Second Programmed Key – Step 1

    Within 10 seconds of turning the ignition to Position 1 (LOCK), INSERT the second previously programmed key into the ignition.

  5. Confirm Second Programmed Key – Step 2

    TURN the ignition from Position 1 (LOCK) to Position 3 (RUN). KEEP the ignition in Position 3 (RUN) for at least 3 seconds, but no more than 10 seconds.

  6. Confirm Second Programmed Key – Step 3

    TURN the ignition to Position 1 (LOCK) and REMOVE the second key from the ignition.

  7. Program New Remote Head Key – Step 1

    Within 20 seconds of turning the ignition to Position 1 (LOCK) and removing the second key, INSERT the NEW un-programmed key into the ignition.

  8. Program New Remote Head Key – Step 2

    TURN the ignition from Position 1 (LOCK) to Position 3 (RUN). KEEP the ignition in Position 3 (RUN) for at least 6 seconds.

  9. Exit Programming Mode

    REMOVE the NEW key from the ignition.

    If the key was successfully programmed, the theft indicator light will illuminate for 3 seconds and then go out to indicate successful programming of the key.

    If the key was NOT successfully programmed, the theft indicator light will FLASH on and off. Wait 20 seconds and repeat the process from Step 1.

  10. Test Remotes

    TEST all remotes. Programming is complete.

  11. Share

    If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.

Important:

  • Verify the following prior to following these instructions:
    • Your vehicle is equipped with keyless entry, and
    • You have a key fob remote that is compatible with your vehicle.
  • Remote Head Key Programming
    • You must have 2 working transponder chip remote head keys in order to program a new remote head key without the assistance of a professional.
    • The key to be programmed must be cut prior to beginning this programming procedure.
  • To program any additional new keys, wait 20 seconds and REPEAT this procedure.

Note: If your vehicle cannot enter programming mode, then you cannot program any remote.  This indicates either no keyless entry installed on the vehicle or a defective keyless entry receiver module.


If you have any difficulties with programming your vehicles, contact us at [email protected].

Key fob remotes

2008 Mercury Sable

NorthCoast Keyless Free Programming Instructions Disclaimer:
  • We worked hard to provide these instructions to our customers. We checked multiple sources to ensure that this information is complete and accurate. However, please understand that we cannot be held liable for any loss due to incorrect use of the programming instructions from www.northcoastkeyless.com.
  • If you cannot program your remote with the instructions that we provide or encounter any discrepancies, please contact us at [email protected] and we’ll make sure that you’re taken care of.

Leave a Reply

Your email address will not be published.

{"cart_token":"","hash":"","cart_data":""}