Easy to Follow Step-by-step Key fob remote Programming Instructions
2007 Chevrolet Silverado (1500, 2500, 3500)
We strive to provide convenience to our customers with free keyless entry remote fob programming instructions for every single vehicle that we sell on NorthCoast Keyless.
Many people don’t know that they can purchase their own replacement vehicle entry remote, save up to 70% off of marked up Dealership prices, and program the replacement remote to their vehicle themselves. We know how good it feels to save money and do something yourself; and we aim to make it as painless as possible for you!
Free Key Fob Remote Programming Instructions for a 2007 Chevrolet Silverado (1500, 2500, 3500)
Time needed: 5 minutes.
KEY FOB REMOTEStep-By-Step How To Programming Instructions
- Close All Doors
CLOSE all doors.
- Enter Programming Mode – Step 1
INSERT key into the Ignition (DO NOT TURN).
- Enter Programming Mode – Step 2
PRESS and HOLD the power UNLOCK button on the Driver’s side door. DO NOT release until instructed.
- Enter Programming Mode – Step 3
TURN the Ignition ON, OFF, ON, OFF
(ON is the position just shy of cranking the engine and OFF is where you can remove your key). - Enter Programming Mode – Step 4
RELEASE the power UNLOCK button on the Driver’s side door.
Upon release of the UNLOCK button, the vehicle should respond by cycling the door locks LOCK / UNLOCK signaling successful entry into Programming Mode.
a. IF the door locks cycle, continue to Step 6. If the door locks cycle BEFORE releasing the UNLOCK button, the vehicle has NOT entered Programming Mode and you must RETURN to Step 1.
b. IF the door locks continue to cycle BEFORE releasing the UNLOCK button, there is a problem with the vehicle’s keyless entry system and the remotes must be programmed by a certified professional Automotive Locksmith or Dealer.
c. IF you are unable to get the door locks to cycle at all, you are turning the key too quick or too slow, there is a problem with your vehicle’s keyless entry system, or the vehicle is not equipped with keyless entry. Check with a certified professional Automotive Locksmith or Dealer. - Program Remote
HOLD the LOCK and UNLOCK buttons on the remote at the same time, up to 30 seconds, until door locks cycle LOCK / UNLOCK to signal successful programming of the remote.
- Program Additional Remotes
REPEAT Step 6 for any additional remotes to be programmed, including working ones.
- Exit Programming Mode
TURN ignition to ON to EXIT Programming Mode.
- Finalize Programming
TURN Ignition to OFF and remove key to finalize programming.
- Test Remotes
TEST all remotes. Programming is complete.
- Share
If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.
Programming Notes:
- Verify the following prior to following these instructions:
- Your vehicle is equipped with keyless entry, and
- You have a key fob remote that is compatible with your vehicle.
- Obtain all remote transmitters for this vehicle. This procedure will erase all previously programmed remotes. You must program all existing and new remotes that you wish to use on the vehicle at this time.
- You may clear your keyless entry system memory by entering programming mode as shown in the steps above.
Time needed: 5 minutes.
PROCEDURE #1 - VEHICLES WITH DRIVER INFO CENTER BUTTONStep-By-Step How To Programming Instructions
- Insert Key Into Ignition
INSERT key into Ignition and TURN the Ignition to ON/ACC (just shy of cranking engine).
- Enter Programming Mode – Step 1
PRESS and HOLD the DISP button on the Radio for 5-10 seconds UNTIL settings are displayed.
- Enter Programming Mode – Step 2
PRESS the SEEK up or down arrows UNTIL “FOB PROG” appears on the display.
- Enter Programming Mode – Step 3
PRESS the PREV or NEXT buttons to enter the sub menu. The menu will display BEGIN.
- Enter Programming Mode – Step 4
PRESS the DISP button to ENTER Programming Mode.
- Program Remote
WHEN the message “PUSH FOB” is displayed, PRESS and HOLD the LOCK and UNLOCK buttons at the same time on the first remote to be programmed for 15 seconds. The vehicle will sound to indicate successful programming of the remote.
- Program Additional Remotes
REPEAT Step 7 for any additional remotes to be programmed, including existing ones.
- Exit Programming Mode
SCROLL until “EXIT” appears on the display. PRESS the DISP button to EXIT Programming. The Vehicle will sound to indicate successful EXIT of Programming Mode.
- Test Remotes
TEST all remotes. Programming is complete.
- Share
If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.
Time needed: 5 minutes.
PROCEDURE #2 - VEHICLES WITHOUT DRIVER INFO CENTER BUTTONStep-By-Step How To Programming Instructions
- Insert Key Into Ignition
INSERT key into Ignition and TURN the Ignition to ON/ACC (just shy of cranking engine).
- Enter Programming Mode – Step 1
PRESS the Trip Odometer Reset button until “RELEARN REMOTE KEY” is displayed.
- Enter Programming Mode – Step 2
PRESS and HOLD the Trip Odometer Reset Button for 3 seconds until “REMOTE KEY LEARNING ACTIVE” displays. Vehicle is now in Programming Mode.
- Program Remote
PRESS and HOLD LOCK and UNLOCK buttons at the same time on the first remote for 15 seconds. The vehicle will emit a sound indicating successful programming of the remote.
- Program Additional Remotes
REPEAT Step 4 for any additional remotes to be programmed, including existing ones.
- Exit Programming Mode
TURN ignition OFF and REMOVE key to EXIT Programming Mode.
- Test Remotes
TEST all remotes. Programming is complete.
- Share
If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.
Programming Notes:
- Verify the following prior to following these instructions:
- Your vehicle is equipped with keyless entry, and
- You have a key fob remote that is compatible with your vehicle.
- Obtain all remote transmitters for this vehicle. This procedure will erase all previously programmed remotes. You must program all existing and new remotes that you wish to use on the vehicle at this time.
- You may clear your keyless entry system memory by entering programming mode as shown in the steps above.
Time needed: 3 minutes.
TRANSPONDER KEYStep-By-Step How To Programming Instructions
- Enter Programming Mode – Step 1
ENTER the vehicle and CLOSE the Driver’s door.
- Enter Programming Mode – Step 2
INSERT working Transponder Key into Ignition and TURN to the ‘ON’ position (just prior to cranking engine), WAIT 1 second and TURN back to the OFF position to successfully enter Programming Mode.
REMOVE key from Ignition. - Program Transponder Key
INSERT NEW key into Ignition and TURN to the ‘ON’ position (just prior to cranking engine).
The key is now programmed to your vehicle. - Test Transponder Key
TEST the new Transponder Key. Programming is now complete.
- Program Additional Transponder Keys
To program additional Transponder Keys, simply repeat the procedure.
- Share
If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.
Programming Notes:
- Verify the following prior to following these instructions:
- You have a transponder key that is compatible with your vehicle.
- You MUST have 1 working transponder key in order for this procedure to work for your vehicle.
- If you DO NOT have 1 working transponder key, you MUST have the key programmed to your vehicle by a professional.
If you have any difficulties with programming your vehicles, contact us at [email protected].
Key fob remotes
2007 Chevrolet Silverado (1500, 2500, 3500)
MONEY BACK GUARANTEE
We offer a No Questions Asked Money Back Guarantee on all of our products!If you can’t get it to work for your vehicle–reach out!We’ll get you your money back.
FAST & FREE SHIPPING
ALWAYS! First Class USPS shipping is always shipped for free for all Domestic (US) customers in less than ONE business day. No ifs, ands, or buts!
CUSTOMER SUPPORT
Have a question for us? Reach out! We're here for you. We will work with you to solve your issue rather than just having you return an item without a solution like some of the big box online stores do.
SAVE 70% OVER DEALERSHIPS
We’ve worked hard to create a network of reliable and reasonably priced suppliers that allow us to give you rock bottom prices.You're also not paying for huge fancy offices or sports cars for our Owners. We always will be just regular people tryin’ to make a livin’ not a killin’!
- We worked hard to provide these instructions to our customers. We checked multiple sources to ensure that this information is complete and accurate. However, please understand that we cannot be held liable for any loss due to incorrect use of the programming instructions from www.northcoastkeyless.com.
- If you cannot program your remote with the instructions that we provide or encounter any discrepancies, please contact us at [email protected] and we’ll make sure that you’re taken care of.
I’ve done that several times in last few days . each time within a few hours both fail to work again , Reprogramed them ,still loose memory in a few hours. Help please!
On my vehicle after I press the odometer button , i dont get a relearn remote key instead i get language english, spanish, french . I then press it again after leaving it on english and i get trip……., then engine hours. Am i doing something wrong, even on the language engilsih, i keep pressing it and nothing comes out. plz help. i have a 2007 chevy silverado classic .
I’m just brought at 2007 Silverado. I’m having same issue, did you figure it out? Thanks
My truck does the same as Jessie Munoz. I’ve tried everything. Why is my truck different from all other instructions. Please help !!!
I have a 2007 Chevy Silverado classic as well and have tried two different key fobs that say are compatible with my truck. I dont have the relearn remote key entry option on my truck as well. How can I do this without taking it to a dealership. I’m tired of when unlocking my truck having to jump in real quick to start it to turn the alarm off. Please help
Language and trip choices only. From reading the owner’s manual it seems these are the choices you have if your vehicle is equipped with DIC buttons(driver information center). I had the same issues and installed the DIC buttons, it did not fix my fob programming issues. I dont know where the programming software resides in the truck so in my case it might be gone because of modifications. I’m sure though what your seeing is because your truck thinks it has the DIC. Good luck.
I have an 07 classic. You are suppose to use the method listed first in this article where you cycle engine on, off, on, off while holding the door unlock button (on the door itself). I’ll try it myself and report back if it works. I got the info from a friend who was a mechanic at a dealership.
I know this is from long ago, but for others … I have a 2007 Chevy Silverado classic as well. I followed first set of instructions. Remember the 3rd step is the unlock button on the *door*