Easy to Follow Step-by-step Key fob remote Programming Instructions
2007 Chevrolet Corvette
We strive to provide convenience to our customers with free keyless entry remote fob programming instructions for every single vehicle that we sell on NorthCoast Keyless.
Many people don’t know that they can purchase their own replacement vehicle entry remote, save up to 70% off of marked up Dealership prices, and program the replacement remote to their vehicle themselves. We know how good it feels to save money and do something yourself; and we aim to make it as painless as possible for you!
Free Key Fob Remote Programming Instructions for a 2007 Chevrolet Corvette
Time needed: 5 minutes.
KEY FOB REMOTE - WITH ONE PROGRAMMED REMOTE
Step-By-Step How To Programming Instructions
- Ensure Vehicle is Off
Vehicle MUST be OFF.
- Gather All Key Fobs
PLACE all key fobs within the interior of the Vehicle.
- Insert Key
INSERT Vehicle key into the key cylinder located at the rear of the Vehicle.
- Enter Programming Mode
OPEN the Trunk and TURN the key 5 times within 5 seconds. The Driver’s Information Center (DIC) will display “READY FOR FOB #X” to signal successful entry into Programming Mode.
- Program Remote
PLACE the new remote in the Glove Box Transmitter Pocket with the buttons facing the Passenger Side of the Vehicle. A beep will sound and the DIC will display “READY FOR FOB #X” to signal successful programming of the remote.
- Program Additional Remotes
REPEAT Step 5 for any additional remotes to be programmed.
- Exit Programming Mode
PRESS the OFF/ACCESSORY button to EXIT Programming Mode.
- Finalize Programming
PRESS the UNLOCK on each key fob to finalize the programming procedure.
- Test Remotes
TEST all remotes. Programming is complete.
- Share
If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.
Time needed: 30 minutes.
KEY FOB REMOTE - WITHOUT A PROGRAMMED REMOTE
Step-By-Step How To Programming Instructions
- Ensure Vehicle is Off
Vehicle MUST be OFF.
- Gather All Key Fobs
PLACE the new remote in the Glove Box Transmitter Pocket with the buttons facing the Passenger Side of the Vehicle.
- Insert Key
INSERT Vehicle key into the key cylinder located on the lower Rear Fascia on the Driver’s side at the rear of the Vehicle.
- Enter Programming Mode – Step 1
OPEN the Trunk and TURN the key 5 times within 5 seconds.
- Enter Programming Mode – Step 2
The Driver’s Information Center (DIC) will display “OFF-ACC TO LEARN.”
- Enter Programming Mode – Step 3
PRESS the OFF/ACCESSORY button.
- Enter Programming Mode – Step 4
The DIC will display “WAIT 10 MINUTES” and will count down to zero.
- Enter Programming Mode – Step 5
The DIC will display “OFF-ACC TO LEARN” again.
- Enter Programming Mode – Step 6
PRESS the OFF/ACCESSORY button.
- Enter Programming Mode – Step 7
The DIC will display “WAIT 10 MINUTES” and will count down to zero again.
- Enter Programming Mode – Step 8
The DIC will display “OFF-ACC TO LEARN” again.
- Enter Programming Mode – Step 9
PRESS the OFF/ACCESSORY button.
- Enter Programming Mode – Step 10
The DIC will display “WAIT 10 MINUTES” and will count down to zero a third time.
- Enter Programming Mode – Step 11
A beep will sound and the DIC will display “READY FOR FOB #1” to signal successful entry into Programming Mode and erasure of all previously programmed remotes from the Vehicle’s memory.
- Program Remote
After a period of time, a beep will sound and the DIC will display “READY FOR FOB #2” to signal successful programming of the first remote.
- Program Additional Remotes
REPEAT Step 2 for any additional remotes to be programmed.
- Exit Programming Mode
PRESS the OFF/ACCESSORY button to EXIT Programming Mode.
- Finalize Programming
PRESS the UNLOCK on each key fob to finalize the programming procedure.
- Test Remotes
TEST all remotes. Programming is complete.
- Share
If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.
Programming Notes:
- Verify the following prior to following these instructions:
- Your vehicle is equipped with keyless entry, and
- You have a key fob remote that is compatible with your vehicle.
- Obtain all remote transmitters for this vehicle. This procedure will erase all previously programmed remotes. You must program all existing and new remotes that you wish to use on the vehicle at this time.
- You may clear your keyless entry system memory by entering programming mode as shown in the steps above.
If you have any difficulties with programming your vehicles, contact us at [email protected].
Key fob remotes
2007 Chevrolet Corvette
MONEY BACK GUARANTEE
We offer a No Questions Asked Money Back Guarantee on all of our products!If you can’t get it to work for your vehicle–reach out!We’ll get you your money back.
FAST & FREE SHIPPING
ALWAYS! First Class USPS shipping is always shipped for free for all Domestic (US) customers in less than ONE business day. No ifs, ands, or buts!
CUSTOMER SUPPORT
Have a question for us? Reach out! We're here for you. We will work with you to solve your issue rather than just having you return an item without a solution like some of the big box online stores do.
SAVE 70% OVER DEALERSHIPS
We’ve worked hard to create a network of reliable and reasonably priced suppliers that allow us to give you rock bottom prices.You're also not paying for huge fancy offices or sports cars for our Owners. We always will be just regular people tryin’ to make a livin’ not a killin’!
- We worked hard to provide these instructions to our customers. We checked multiple sources to ensure that this information is complete and accurate. However, please understand that we cannot be held liable for any loss due to incorrect use of the programming instructions from www.northcoastkeyless.com.
- If you cannot program your remote with the instructions that we provide or encounter any discrepancies, please contact us at [email protected] and we’ll make sure that you’re taken care of.
2007 Vette….it has quit recognizing both FOBs. Put new batteries in both. Gone thru the 10 minute procedures numerous time. It gets to the Beep part and I wait for additional beep….but it never comes and eventually the DIC goes dark. It then says it does not recognize either FOB….. Car is in my driveway, window down and no way to move it…. Any suggestions…? I should add that it quit recognizing Fob 1 several years ago, then it quit recognizing FOB 2 but it would start with Fob 2 inserted in the jockey box receptical. It no longer starts with Fob 2….