2000 GMC Sierra (1500, 2500, 3500) Keyless Entry Remote Programming Instructions

Step-by-Step How To Programming Instructions for a 2000 GMC Sierra (1500, 2500, 3500) Keyless Entry Remote Fob

We strive to provide convenience to our customers with free keyless entry remote programming instructions for every single vehicle that we sell on NorthCoast Keyless.

Many people don’t know that they can purchase their own replacement vehicle entry remote, save up to 70% off of marked up Dealership prices, and program the replacement remote to their vehicle themselves. We know how good it feels to save money and do something yourself; and we aim to make it as painless as possible for you!

Free Step-by-Step How To Programming & Memory Clearing Instructions for a 2000 GMC Sierra (1500, 2500, 3500) Keyless Entry Remote Fob

Verify that this important information is on the back of your remote before using these programming instructions.

FCC ID: KOBUT1BT

Factory Part No: 15732803

Programming Notes:

Obtain all remote transmitters for this vehicle. This procedure will erase all previously programmed remotes. You must program all existing and new remotes that you wish to use on the vehicle at this time.

 

Keyless Entry System Memory Clearing Instructions are noted in the dark blue colored steps below.

Step-by-Step How To Programming Instructions:

  1. Close all doors.
  2. Insert key into the ignition.
  3. Press and hold the power UNLOCK button on the Driver’s side door panel. Do not release until instructed to do so.
  4. Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just shy of starting your vehicle, OFF is the position where you can remove your key)
  5. Release the power UNLOCK button on the Driver’s side door panel. Upon release of the UNLOCK button, the vehicle should respond by locking and unlocking automatically signaling programming mode has been reached. If the locks on your vehicle cycle, continue to Step 6. If the door locks LOCK and UNLOCK BEFORE releasing the UNLOCK button, the vehicle has NOT entered programming mode and you must start over (remove key, open door and return to Step 1). If the vehicle continues to LOCK and UNLOCK BEFORE releasing the UNLOCK button, there is a problem with the vehicle’s keyless entry system and the remotes must be programmed by a certified professional. If you are unable to get the door locks to cycle at all, you are turning the key too quick or too slow.
  6. Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30 seconds.
  7. Repeat Step 6 for all additional remotes to be programmed.
  8. After Step 6 has been performed for all remotes TURN ignition to ON to exit programming mode.
  9. Turn ignition to OFF and remove key.
  10. Test all remotes. Programming is now complete.
  11. If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.
Save On Your Purchase by Sharing with Friends!
You about to save some mega moolah with NorthCoast Keyless! Save even more by sharing your purchase with friends and you will receive a special discount at checkout!


If you have any difficulties with programming the remote you ordered from us to your vehicle, check out our FAQ Page for common questions, mistakes, and solutions to programming keyless entry remotes to your vehicle. Always feel free to contact us at support@northcoastkeyless.com.

View our entire catalog of FREE GMC keyless entry remote programming instructions!

Need to buy a 2000 GMC Sierra (1500, 2500, 3500) keyless entry remote fob? We’ve got you covered!

Out of stock
Dealership: $150.00
$24.94

 

Need a new battery for your 2000 GMC Sierra (1500, 2500, 3500) keyless entry remote fob? We’ve got that too!

Remote Accessories

CR2032 Lithium Coin Battery

Rated 5.00 out of 5
Dealership: $8.00
$3.94

Our Free Programming Instructions Disclaimer can be found on the NorthCoast Keyless FAQ page.

One thought on “2000 GMC Sierra (1500, 2500, 3500) Keyless Entry Remote Programming Instructions

  1. Michael Van Gilst says:

    I tried the instructions for programming my 2000 GMC Sierra 1500 key fob and not only could I not get it to work, now my doors won’t lock at all from the inside. Any ideas what happened?

Leave a Reply

Your email address will not be published.